Construction & Trades

How to Calculate Pipe Offset: A Step-by-Step Guide

Plumber installing steel pipe fittings indoors

A pipe has to move over, up, or around something, and it has to do it without kinking, forcing a joint, or wasting a length of pipe. That move is an offset, and it is one right triangle. Once you know the offset and the fitting angle, the travel and the run follow from two multiplications, and a pipe offset calculator just does that arithmetic for you. Here is how the math works, in the order you would use it on the job, with a full worked example.

Try it: Pipe offset calculator

What an offset is: offset, travel, and run

An offset is a change in a pipe’s centerline to get around an obstacle or line up with a connection, made with two matching fittings. Three measurements describe it:

Offset (set). The perpendicular distance between the two parallel centerlines. This is the number you measure first, center to center.

Travel. The center-to-center length of the angled section between the two fittings. It is the hypotenuse of the offset triangle, and it is the length the pipe actually takes through the offset.

Run (advance). How far along the original direction the offset takes to complete. This is the number that decides whether the offset fits in the space you have.

A rolling offset moves the pipe both up and down (rise) and sideways (spread or roll) at the same time. You solve it by finding the true offset, the diagonal across the rise and spread, and then treating it like a simple offset. The rest of this guide uses the same two formulas for both kinds.

The two formulas, and the multiplier table

Travel and run come from the fitting angle. If theta is the fitting angle:

Travel = offset x (1 / sin angle). The 1 / sin part is the travel multiplier, also called the cosecant.

Run = offset x (1 / tan angle). The 1 / tan part is the run multiplier, also called the cotangent.

Nobody works these out from sine tables on the job. Fitters use the multipliers for the five standard fitting angles, and the calculator shows both multipliers with every answer so you can double-check on a job-site calculator:

Fitting angleTravel multiplierRun multiplierTravel for 6″ offsetTravel for 12″ offsetTravel for 24″ offset
11.25 deg5.1265.02730.76″61.51″123.02″
22.5 deg2.6132.41415.68″31.36″62.72″
30 deg2.0001.73212.00″24.00″48.00″
45 deg1.4141.0008.49″16.97″33.94″
60 deg1.1550.5776.93″13.86″27.71″

The 45 degree multiplier of 1.414 is the one most fitters know by heart. The 30 degree multiplier is the easiest to use in your head: travel is exactly twice the offset, and the run is the offset times 1.732.

Worked example: a 12-inch offset with 45-degree elbows

A pipe has to move 12 inches sideways, using 45 degree elbows. The fitting angle is 45 degrees, so the travel multiplier is 1.414 and the run multiplier is 1.000.

Travel: 12 x 1.414 = 16.97 inches, which rounds to 17 inches at the nearest sixteenth.

Run: 12 x 1.000 = 12 inches.

That is the center-to-center length. The pipe you cut is shorter, because each fitting eats into it. A 2-inch long-radius 45 degree butt-weld elbow is about 1 3/8 inches center to end, so the takeout is 1.375 inches per fitting:

Cut length: 16.97 – (2 x 1.375) = 14.22 inches, about 14 1/4 inches, before subtracting your weld gaps.

Check your own fitting chart for the takeout. Takeouts vary by fitting size, radius, and maker, and the chart beats any rule of thumb.

Rolling offsets: rise and spread first

A rolling offset has two numbers instead of one: how far the pipe rises and how far it spreads sideways. The first step is to combine them into a single true offset:

True offset = square root of (rise squared + spread squared).

Then use the true offset exactly like a simple offset: multiply by the travel multiplier and the run multiplier for your fitting angle.

Take a line that has to come up 8 inches and over 6 inches to reach a connection, using 45 degree fittings:

True offset: square root of (8 squared + 6 squared) = square root of 100 = 10 inches.

Travel: 10 x 1.414 = 14.14 inches, or 14 1/8 inches.

Run: 10 x 1.000 = 10 inches.

The 6-8-10 numbers here are on purpose: they are a scaled 3-4-5 triangle, and checking a layout with 3-4-5 is a quick way to confirm a square corner on the job. Real rolls rarely come out this clean, so let the calculator handle the square root.

A bigger roll works the same way. With a 15-inch rise and a 20-inch spread, the true offset is 25 inches, and 45 degree travel is 35.36 inches.

Copper plumbing fittings arranged in a row

Choosing a fitting angle

The angle you pick changes the shape of the offset, not just the numbers:

45 degrees is the default for most piping. It is compact, easy to fit, and the 1.414 multiplier is well known.

22.5 and 11.25 degrees make gentle offsets that are kinder to flow and drainage, but they need a lot more run. That extra run is the price of the gentle angle.

60 degrees is short and steep. It is common in electrical conduit, where offsets are made by bending rather than fittings.

30 degrees is a good compromise when 45 degrees is too long vertically and the math needs to stay simple.

The run decides whether your angle fits. Say you need an 18-inch offset with 22.5 degree fittings to clear a beam flange:

Travel: 18 x 2.613 = 47.04 inches, or 47 1/16 inches.

Run: 18 x 2.414 = 43.46 inches, or 43 7/16 inches.

Shallow fittings use more horizontal space. If you only have 30 inches of run to work with, a 22.5 degree offset will not fit, but 45 degree fittings (18 inches of run) will. Always check the run against the space before you cut.

Cut length and takeouts

Travel is center to center, not the length to cut. The cut length is:

Cut length = travel – takeout of fitting 1 – takeout of fitting 2, then subtract weld gaps or add socket depth as your joint requires.

Each fitting eats into the pipe, so subtract one takeout for each end. Takeouts depend on fitting size, radius, and type, so use the manufacturer’s chart. Fractions are rounded to the nearest sixteenth of an inch. Keep three decimal places until the final cut, then round, because rounding early is how a cut comes up short.

Common mistakes

  • Measuring to the pipe edge instead of the centerline. All offset math is center to center. Measure from the center of one pipe to the center of the other, not from edge to edge.
  • Using the angle of the bend instead of the fitting. A “45” fitting changes direction by 45 degrees. Use that number, not the angle between the two pipe pieces.
  • Forgetting both takeouts. Each fitting eats into the pipe. Subtract one takeout for each end, plus a weld gap or socket depth if your joint has one.
  • Rounding too early. Keep three decimal places until the final cut, then round to the nearest sixteenth.
  • Ignoring the run on a rolling offset. On a roll, the run equals the true offset times the run multiplier, not the rise or the spread alone.

Frequently asked questions

How do you calculate a 45-degree offset?

Multiply the offset by 1.414 to get the travel, the center-to-center length between the two 45-degree fittings. The run is equal to the offset. A 10-inch offset has 14.14 inches of travel and 10 inches of run.

How do you figure a rolling offset?

Square the rise and the spread, add them, and take the square root to get the true offset. Then multiply the true offset by the travel multiplier for your fitting angle. With a 15-inch rise and 20-inch spread, the true offset is 25 inches and 45-degree travel is 35.36 inches.

What is travel in pipefitting?

Travel is the center-to-center length of the angled section of an offset, measured from where the centerline crosses one fitting to where it crosses the other. It is the hypotenuse of the offset triangle.

What is the difference between offset and run?

The offset is the distance the pipe moves sideways, perpendicular to its path. The run is the distance it advances in its original direction while making that move.

Can I calculate a 90-degree offset?

A 90-degree change of direction is not an offset in this sense. It is two 90-degree elbows with a straight section of pipe between them, and there is no offset triangle to solve. The pipe offset calculator covers fitting angles from 11.25 to 60 degrees. For a 90-degree turn, lay out the two elbows and the straight piece between them instead.

How do you get the cut length of an offset?

Start with the travel, subtract the takeout of each fitting, and subtract any weld gap or add socket depth as your joint requires. Takeouts depend on fitting size, radius, and type, so use the manufacturer’s chart.

This guide is for general education and uses the same formulas as the OrbCalc pipe offset calculator. Verify takeouts against your fitting manufacturer’s chart and measure before cutting.

More construction guides: how to calculate board feet, how to calculate voltage drop, and how to pick the right wire size. See all construction calculators.

Try the calculators

Related guides